■2 Short Torx Screws Trijicon RMR SRO Mounting Red Dot Sight Glock ZEV Slide hex

Description

■ (2) brand-new Torx head screws for mounting your Trijicon RMR or SRO to any ZEV, Lantac or various Brownells* milled slides.
■
Made in the
U
S
A
.  I know what's on the line if you use incorrect screws.  If they're too long, they'll interfere with the extractor depressor plunger assembly and you will have extraction issues.  My screws will not interfere with any part of the cycling.
■ These high-quality screws are SHORT, approx. 1/4" long (length measured from the top of the head), or 0.14" long (length measured from the bottom of the tapered head - see photos).  They are shorter than the screws that come with your Trijicon RMR/SRO.
■ To fasten these screws, you can use an IP10 Torx-Plus™ wrench, a T10 Torx™ wrench, or the ZEV (WREN-TORX) Torx™ wrench.
■ These screws can be used whether or not you decided to install the OPT-GASK-RMR (thin metal) gasket.
■ These are among the STRONGEST (tensile strength) screws you can buy.
■ These screws are angled under the head to sit flush within countersunk holes. The black-oxide finish provides mild corrosion resistance. The Torx-Plus™ drive has more points of contact than hex, Phillips, or slotted drives, allowing you to apply extra force (not that you want to) with less slippage or damage to the recess.  Plus, when installed, Torx-head screws look SO much better than phillips-head, or even hex-head screws!
■
How to install:
According to the technicians at ZEV Technologies, apply a small amount of
threadlocker (
Loctite™
) BLUE to the threads.
(Note: Do NOT use RED threadlocker or it will be difficult to remove the screws unless you heat the screws)
.  After applying the threadlocker, screw-in the screw.  Then, back it out.  Then, screw it back in so that you distribute the threadlocker evenly.  Do not apply a lot of torque.  Only hand-tighten a little past the point of being snug, which is about 1-1/2 turns.  To be precise, that's between 9 to 11
inch
-pounds of torque.
■ For those that select free shipping, these screws will be shipped in a plastic bag, within a rugged & secure Tyvek
™
(won't tear) envelope.
■ Buy from a reputable seller (me :)
I've sold over * 900 * of these sets (eBay verified above), with 100% Buyer Satisfaction and 100% Positive Feedback.
Please read all of the positive feedback I have received on these screws.
I am the original seller of these screws, and have sold them for 8 years.  So, regardless of what you read, other sellers have plagiarized MY listing.
■
NOTE!!!  I also have a few sets of these screws made in Stainless Steel.  So, if you prefer the "Silver-Look" over black, just request Stainless Steel in the "Message To Seller" area when you check out.
*********************************************************************************************************************
***    BONUS !!!   Buy (3) Sets, and I'll ship a (4th) Set FREE!!!  (It's always good to have spares)      ***
*********************************************************************************************************************
Can be used with
ANY
Zev slide!  Why?  Because
ALL
Zev slides have the raised & threaded "bosses" (or mounting posts) for the RMR to affix onto
.
Here are only some of the Zev slides in which these screws can be used:
SLD-Z17-3G-DFLY-RMR-CW.ABS-BRZ
SLD-Z17-3G-DFLY-RMR-CW.ABS-DLC
SLD-Z17-3G-ESOC-DPP-DLC
SLD-Z17-3G-ESOC-DPP-FDE
SLD-Z17-3G-ESOC-RMR-CW.ABS-FDE
SLD-Z17-3G-ESOC-RMR-CW.ABS-GRY
SLD-Z17-3G-HEX-RMR-CW.ABS-FDE
SLD-Z17-3G-HEX-RMR-CW.ABS-GRY
SLD-Z17-3G-OMEN-RMR-DLC
SLD-Z17-3G-OMEN-RMR-GRY
SLD-Z17-3G-ORION-RMR-DLC
SLD-Z17-3G-ORION-RMR-GRY
SLD-Z17-3G-PRZF-RMR-CW.ABS-DLC
SLD-Z17-3G-PRZF-RMR-CW.ABS-GRY
SLD-Z17-3G-TRI-RMR-CW.ABS-DLC
SLD-Z17-3G-TRI-RMR-CW.ABS-FDE
SLD-Z17-4G-DFLY-RMR-CW.ABS-BRZ
SLD-Z17-4G-DFLY-RMR-CW.ABS-DLC
SLD-Z17-4G-ESOC-DPP-DLC
SLD-Z17-4G-ESOC-DPP-FDE
SLD-Z17-4G-ESOC-RMR-CW.ABS-FDE
SLD-Z17-4G-ESOC-RMR-CW.ABS-GRY
SLD-Z17-4G-HEX-RMR-CW.ABS-FDE
SLD-Z17-4G-HEX-RMR-CW.ABS-GRY
SLD-Z17-4G-OMEN-RMR-DLC
SLD-Z17-4G-OMEN-RMR-GRY
SLD-Z17-4G-ORION-RMR-DLC
SLD-Z17-4G-ORION-RMR-GRY
SLD-Z17-4G-PRZF-RMR-CW.ABS-DLC
SLD-Z17-4G-PRZF-RMR-CW.ABS-GRY
SLD-Z17-4G-TRI-RMR-CW.ABS-DLC
SLD-Z17-4G-TRI-RMR-CW.ABS-FDE
SLD-Z17-5G-OMEN-RMR-DLC
SLD-Z17-5G-OMEN-RMR-GRY
SLD-Z17-5G-ORION-RMR-DLC
SLD-Z17-5G-ORION-RMR-GRY
SLD-Z19-3G-DFLY-RMR-CW.ABS-BRZ
SLD-Z19-3G-DFLY-RMR-CW.ABS-DLC
SLD-Z19-3G-ESOC-DPP-DLC
SLD-Z19-3G-ESOC-DPP-FDE
SLD-Z19-3G-ESOC-RMR-CW.ABS-FDE
SLD-Z19-3G-ESOC-RMR-CW.ABS-GRY
SLD-Z19-3G-HEX-RMR-CW.ABS-FDE
SLD-Z19-3G-HEX-RMR-CW.ABS-GRY
SLD-Z19-3G-OMEN-RMR-DLC
SLD-Z19-3G-OMEN-RMR-GRY
SLD-Z19-3G-ORION-RMR-DLC
SLD-Z19-3G-ORION-RMR-GRY
SLD-Z19-3G-SPART-RMR-GRY
SLD-Z19-3G-TRI-RMR-CW.ABS-DLC
SLD-Z19-3G-TRI-RMR-CW.ABS-FDE
SLD-Z19-4G-DFLY-RMR-CW.ABS-BRZ
SLD-Z19-4G-DFLY-RMR-CW.ABS-DLC
SLD-Z19-4G-ESOC-DPP-FDE
SLD-Z19-4G-ESOC-RMR-CW.ABS-FDE
SLD-Z19-4G-ESOC-RMR-CW.ABS-GRY
SLD-Z19-4G-ESOC-RMR-DLC
SLD-Z19-4G-ESOC-RMR-FDE
SLD-Z19-4G-HEX-RMR-CW.ABS-FDE
SLD-Z19-4G-HEX-RMR-CW.ABS-GRY
SLD-Z19-4G-OMEN-RMR-DLC
SLD-Z19-4G-OMEN-RMR-GRY
SLD-Z19-4G-ORION-RMR-DLC
SLD-Z19-4G-ORION-RMR-GRY
SLD-Z19-4G-TRI-RMR-CW.ABS-DLC
SLD-Z19-4G-TRI-RMR-CW.ABS-FDE
SLD-Z19-5G-OMEN-RMR-DLC
SLD-Z19-5G-OMEN-RMR-GRY
SLD-Z19-5G-ORION-RMR-DLC
SLD-Z19-5G-ORION-RMR-GRY
SLD-Z34-3G-DFLY-RMR-CW.ABS-BRZ
SLD-Z34-3G-DFLY-RMR-CW.ABS-DLC
SLD-Z34-3G-PRZF-RMR-CW.ABS-DLC
SLD-Z34-3G-PRZF-RMR-CW.ABS-GRY
SLD-Z34-4G-DFLY-RMR-CW.ABS-BRZ
SLD-Z34-4G-DFLY-RMR-CW.ABS-DLC
SLD-Z34-4G-DFLY-RMR-GRY
SLD-Z34-4G-PRZF-RMR-CW.ABS-DLC
SLD-Z34-4G-PRZF-RMR-CW.ABS-GRY
* These screws will also work with Lantac and Brownells' slides with raised threaded bosses/mounting posts.
These short screws can also be used for mounting the following ZEV Cover Plates to your ZEV slide:
ADAP-DPP-SS-ZEV-SM
ADAP-RMR-SS-45-BLNK-SM
NOTE: This listing is ONLY for the (2) screws. It does NOT include the slide, RMR or any other items shown in the photos!!!
*** PLEASE NOTE MY SHIPPING TERMS BEFORE CONTACTING ME:
In order to keep shipping free, I ship USPS Economy Shipping.  Although I guarantee that I will ship your screws within 1 business day, and most of my customers receive their screws relatively quickly (as you can read in my feedback), it can take up to
12 BUSINESS DAYS
to get to you, REGARDLESS of what Ebay states is your guaranteed/estimated delivery date.  PLEASE allow
12 BUSINESS DAYS
before contacting me to ask, "Where are my screws?".
If you can not wait this amount of time
, please select the Expedited (faster) shipping option which includes a tracking #.  Thank you for understanding.
Also, regarding PayPal, due to some recent payment disputes, I will only ship to the address on your PayPal account!  If you need it shipped to an alternate address, please add that alternate address to your PayPal account **BEFORE** sending payment.
Returns:
Returns accepted only if the screws do not fit your Zev, Brownells, or Lantac slides with raised bosses/mounting posts.
RM01 RM02 RM04 RM05 RM06 RM07 RM08 AC32085 red dot vortex mount mounts fine thread ac32064 4 - 40 1/4" 4-40 1/4 4-40 machine head screws black oxide hardware SI-RMR-SCREWS brownells brownell's Kit